Найти Единая Ультразвуковая, Ультразвуковая Сварка , Ультразвуковой Сварочный Аппарат на Промышленность Directory, надежный производитель / поставщик / завод из Китая

Корзина запроса (0)
Главная > Перечень Продуктов > Единая Ультразвуковая > K3530 Серии Единая Ультразвуковой Пластичный Welder

K3530 Серии Единая Ультразвуковой Пластичный Welder

Базовая информация

Модель: K3530 / K3531

Описание продукта

Технические характеристики K3530 серии ультразвуковой пластичный welder \Н1. Фрэ:35 кГц \Н2. ПВ:900ВТ/1200ВТ \Н3. Генератор Кобра:режим таймера \Н4.K3531 серии опционально \Н\Н

 

 K3531 Series Ultrasonic Welder

1.Frequency:35KHz

2.Power:900W/1200W

3.Cobra generator:Timer mode

 

 

 

Ultrasonic Welding Machine

Ultrasonic welding of thermoplastics is cost effective because it cuts manufacturing time. Ultrasonic welding is now a widely accepted process, having been first introduced in the early 1960's.

The type of thermoplastic, the design of the parts to be welded and the design of the joint are of great important but often neglected. To take full advantage of the benefits of ultrasonic welding it is advisable to choose carefully the design of the parts, especially the joint.

It is advisable to take into consideration the different welding properties of amorphous and semi-crystalline thermoplastics when choosing the resin to be used. The selection of the plastic and the design of the critical in getting dependable and reproducible welds.

Of course, parts should be free of injection molding problems and inconsistencies such as bubbles, burned material, internal stress and sink marks resulting from the injection molding process.

Here are some factors to consider in order to achieve the best results with ultrasonic welding:
Strength requirements of the welded joint
Is a hermetic seal required
Appearance requirements
Is flash permissible
If there is a degree of flexibility on plastic resin, which resin will meet the design requirements and be best for ultrasonic welding
Positioning and type of joint design
Parts design for ease of assembly before welding
Fixture design to hold the parts in position during welding
Will it be possible to make a horn to get the required ultrasonic energy into the joint

 

LTRASONIC WELDING TECHNIQUE


WELDING:
The typical profile of a joint design for ultrasonic welding has two functions:

1. Its shape of a groove and tongue eases positioning during assembly and maintains in place the parts during the welding cycle

2. The energy director in the joint concentrates the energy to a small area and supplies at the same time the necessary material for an optimal welding joint. The profile of the joint area depends largely on the purpose of the application; it can therefore be shaped quite differently. The settings of the machine, like welding pressure and amplitude, are adjusted to produce a movement of the horn front in phase with the part to be welded. The second part placed in the fixture must stay passive. The motional interference produces friction in the contact area of the two parts. Due to this highly intensive ultrasonic vibration the joint area melts together immediately. Under the pressure applied simultaneously and some fractions of a second longer than the ultrasonic impulse lasts the melted area solidifies and an inseparable joint is produced.

STAKING:
Ultrasonic staking is used to assemble injected plastic parts with parts of another material. Studs on the molded plastic part penetrate the second article to be mounted. The projecting part of these studs is formed into riveting heads with a specially shaped horn tip. The cavity in the horn is big enough to hold the displaced material and form it nicely. The amplitude of the horn has to be adjusted for maximum motional interference between oscillating horn tip and plastic stud. Heat is then produced by friction between the plastic part and the horn tip, which allows an immediate melting in this area. The pressure controlled by the welding machine lets the riveting head solidify after a short hold time. Multi-tip horns are often used for simultaneous staking of different areas on the same part.

 

SPOT WELDING:
Ultrasonic spot welding is used whenever large plastic parts cannot be placed on a traditional machine. Therefore, the welding head designed as a handgun is brought to the part; either manually or with a robot. The advantage of ultrasonic spot welding is the fact that the parts do not need any special preparation (no energy director required). Therefore large size vacuum formed parts can also be assembled easily.
The ultrasonic horn is built to produce high amplitude. The tip of the horn is shaped in order to penetrate the two layers of material, leaving a typical ring pattern on the workface, while the backside rests smooth and clean.

INSERTION OF METAL PIECES:
A metal piece such as a threaded insert or bolt has to be embedded into an existing hole in a plastic part. The metal piece is contacted by the oscillating horn, which creates friction between the two parts melting the plastic material. The machine pressure displaces the now melted material into the structure on the metal part surface. Once the displaced material has solidified the inserted piece remains tightly seated and resists to tensional as well as to torsion forces.

 
 
\п \п
 
 
 
 
WELDING
 

STAKING

 
SPOT WELDING
 
INSERTION OF METAL PIECES
 
   
   
\п\п

Группа Продуктов : Единая Ультразвуковая

Горячие продукты
K3530 Серии Единая Ультразвуковой Пластичный WelderApsonic ультразвуковой генератор Кобра (20кГц)2017 выдающиеся горячей плиты пластичный Сварочный аппаратПанель солнечных батарей ультразвуковой сварочный аппаратУльтразвуковой автомат для резки волокна или PE и т. д. органопластиковУльтразвуковой Процессор жидким sonochemistry для извлечения нарушения эмульгатор, используемый в Фабрике20кГц Оптовая ODM имеющиеся автозапчастей ультразвуковой Рожочок(плесень)Ультразвуковой Пластиковая Трубка Запайки Машины Генератора Ручной ультразвуковой пластичный автомат для резки 30 кГц ультразвуковой резак4200w ультразвуковой Автоматический Устранимый медицинский лицевой щиток Гермошлема делая машину 2000Вт Автоматическая экономически эффективный ультразвуковой сварки машина для лития батареяCE одобрил БДС Автоматический ультразвуковой Сплетенный ярлык резки машиныБДС поставку замена высокое powe ультразвуковой сварки ультразвуковой сварочный аппарат / усилитель / преобразователь для сварки пластмассБДС снабжение цене высокочастотного промышленного использования 15к ультразвуковой пластичный Сварочный аппарат для ПВХ,ПЭ,ПП нетканые ткани с CEБДС handheld ультразвуковой камамбер пищевыми продуктами / ткани резки резак ножБДС дунгуань ультразвуковой точности Автоматическая машина высокой частоты пластиковых сварочный аппарат/ сварочные аппараты